6" X 30" Bottom Arbor Gang

To gang rip flitches or cants into boards with a maximum cant thickness of 6-1/2".

Infeed Section

• 10 ft. long with four (4) non-powered, 6" diameter rolls mounted on 1-15/16" shafts and bearings. No guide fence included.

Center Section

• Inside machine width is 30" which allows for a feed roll length of 29" and a press roll length of 24".
• 5/8" thick steel side plates, bored and machined for proper fitting. Side plates set on a 6" wide flange beam base which also incorporates the motor mount.
• Two infeed side and two outfeed side feed rolls are included. Rolls are 6" diameter, mounted on 1-15/16" shafts and bearings and incorporate COLEMAN teeth.
• Feed roll drive utilizes a 5 HP motor and speed reducer with #80 roller chain, which will feed the machine at 50 feet per minute (FPM).

OTHER FEED RATES ARE AVAILABLE, BUT ENTIRE APPLICATION INCLUDING MAIN MOTOR HP, SAW ARBOR DIAMETER, NUMBER OF SAWS IN CUT AT ONE TIME, AND FEED SPEED MUST BE CONSIDERED.

• One infeed side and one outfeed side press roll assembly is included. Rolls are 8" diameter, mounted on 1-15/16" shafts and bearings and incorporate COLEMAN teeth. Press rolls are powered from the feed roll drive, and are air activated with both, down and up pressure.
• Standard 6" machine uses a 19" diameter sawblade with a minimum of thickness for ripping of 1/2" & a maximum thickness for ripping of 6-1/2". SAWBLADES ARE NOT INCLUDED.
• Saw arbor is 2-15/16" in diameter, double keyed and supported by three ball bearings. Steel is 1045 turned, ground and polished (TG&P). Arbor is designed for a direct connected motor drive.
• Front & top safety fingers are included. All necessary guards are in place, and rear cant support fingers are included.

Outfeed Section

Incorporates a live belt which is driven from the feed roll drive and is 24" wide by 14' long. Sides of the conveyor are 4" high and give an overall inside width of 26".

OPTIONS:

Infeed Section

1. Manually adjustable laser mounting assembly, without laser lights.
2. Laser lights.
3. Extend infeed length:
   • A. Without roll, frame only per foot
   • B. Additional roll and frame per foot
4. Two strand, reversible, cant positioning chain using #80 roller chain and 2 HP electric drive, lifted by air bags
5. For third strand add
6. Adjustable guide fence which is positioned manually by loosening bolts, moving and re-tightening bolts
7. Moveable guide fence operated by hand lever which shifts fence through rack and pinion operation

Center Section

1. Additional width per 6" up to 42" of width with COLEMAN teeth
2. Two speed feed works (2nd motor and drive)
3. Main arbor motor and drive, and adjustable motor base

   FOR 200 HP LINCOLN MOTOR, 1800 RPM, DRIP-PROOF ENCLOSURE, MOTOR COUPLING TO SAW ARBOR, MOUNTED AND ALIGNED, ADD $5,670.00. THIS PRICE IS TO BE USED ONLY AS A GUIDE LINE. PRICE IS SUBJECT TO CHANGE WITHOUT NOTICE.

4. Overhead motor mount
5. Knurled and chromed rolls:
   • Four feed rolls for 30" machine
   • Two press rolls for 30" machine

COLLARS AND SPACERS:

1. Gang collars (need 1 each per gang or each stationary saw)
   • stationary
   • starting
   • finishing
   • bolt kit (must determine length)
2. Spacers
   • Up to 2"
   • 2-1/16" to 3"
   • Greater than 3"

Note:
Horsepower of main motor must be calculated with facts, NOT guesswork. Consult engineering for your exact requirements. You must know: species; maximum number of saw blades in the cut at one time; feed rate desired to accomplish customers production; kerf of sawblades.

Return to Gangs Page